![]() ![]() ![]() Setup using the UISP ™ app requires the U-Installer, sold separately. You can also manage your device using the Ubiquiti Internet Service Provider Application. For details, refer to the User Guide available at ui.com/download/airmax The airOS Configuration Interface will appear, allowing you to customize your settings as needed. You must agree to the Terms of Use to use the product. Enter ubnt in the Username and Password fields.Launch your web browser and type in the address field.Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.Make sure that your host system is connected via Ethernet to the device.Verify connectivity in the airOS Configuration Interface. The PowerBeam mounted outdoors without the Reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only. The PowerBeam mounted outdoors with the Reflector installed provides directional outdoor coverage (gain is reflector-dependent). The Power LED will light green when the device is connected to a power source. The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity. In airOS®, you can modify the threshold values for the wireless signal strength LEDs on the Advanced tab under Signal LED Thresholds. If you need to remove the Antenna Feed, you must depress the Release button first. This ensures that the Antenna Feed is locked into place. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.Īfter you assemble the device, check the Release button it should be fully engaged in the Release Button Slot of the Rear Housing. ![]() To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. For more details, visit ui.com/toughcable Hardware Overview We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.IEC 68-2-5 at 40° C (104° F), Equivalent: ETS 300 019-1-4ĮTS 300 019-1-4, Equivalent: MIL-STD-810 G Method 506.* The PBE-M5-400 Antenna Feed has a thin gray ring around the center of the cap to differentiate it from the PBE-M5-300 Antenna Feed. Software-Adjustable to Correspond to Custom RSSI Levels PBE-M5-400-ISO System and Regulatory/Compliance Long Distance: Capable of high‑speed, carrier-class links. Scalability: High capacity and scalability. Intelligent QoS: Priority assigned to voice/video for seamless streaming. This time slot method eliminates hidden node collisions and maximizes airtime efficiency, so airMAX technology provides performance improvements in latency, noise immunity, scalability, and throughput compared to other outdoor systems in its class. Unlike standard Wi-Fi protocol, Ubiquiti’s Time Division Multiple Access (TDMA) airMAX protocol allows each client to send and receive data using pre-designated time slots scheduled by an intelligent AP controller. Providing high performance and innovative mechanical design at a low cost, the PowerBeam ISO is extremely versatile and cost‑effective to deploy. This improves performance because it eliminates cable losses. Ubiquiti’s InnerFeed™ technology integrates the radio into the feedhorn of an antenna, so there is no need for a cable. This is especially important in an area crowded with other RF signals of the same or similar frequency. With its combination of focused beam directivity and RF isolation, the PowerBeam ISO blocks noise to improve noise immunity. The PowerBeam ISO directs RF energy in a tighter beamwidth, and its integrated isolator design improves RF isolation to spatially filter out interference. Ubiquiti Networks launches the PowerBeam™ ISO, an airMAX Bridge that is ideal for deployments requiring maximum performance and RF isolation.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |